Sewing-machine parts · Tilžės g. 68, Šiauliai

Chosen for the thread, not the machine.

A needle has to carry a thread through a cloth. Too fine for the thread and the cloth files the thread away until it shreds; too coarse for the cloth and it leaves a hole you can see. Tell us both, and the size follows.

Tuesday to Saturday, 9 to 18+370 41 439 062

  • 60fine
  • 80the usual
  • 100heavier
  • 120heaviest

Blade width drawn to the size number: hundredths of a millimetre across. The red line is the thread lying in the groove.

Turn the gauge and watch the groove

The size number is the blade across, in hundredths of a millimetre. Every figure under the drawing comes out of that one number and the drawing itself — nothing here is written beside the picture.

The blade in section, groove to the rightThe hole it leaves in a plain cotton

Across the blade
0.600.801.001.20mm
Groove, a third of that
0.200.270.330.40mm
Thickest thread it shelters
295281117tex
Yarns the blade pushes aside
2.02.73.34.0

Fine thread into fine cloth. Anything thicker than about 29 tex rides on the outside of the groove instead of in it, and the cloth files away at it until it shreds.

The size this counter sells most of. The groove takes an ordinary all-purpose thread with room to spare, and the hole closes up on anything but the finest weave.

Heavier thread sits right down in the groove. The hole it leaves is wider than three of the cloth's own yarns, so on a fine weave you will see where the needle went.

For thread the finer blades cannot shelter. It pushes four yarns aside and leaves a hole you can see, which is why it belongs in cloth that can carry one.

Drawn at a hundred pixels to the millimetre, so the circle's radius on screen is the size number itself. The groove is drawn at a third of the blade. The thread shown is the thickest one that depth will shelter, taking a thread's width as 0.037 millimetres times the square root of its tex number. The cloth is a plain cotton with three tenths of a millimetre between yarn centres. This dial knows nothing about your machine: it will not promise you a stitch, it names no make, and it cannot tell you a part fits a model we have not been told.

Three off the wall at that size

What we put on the counter for fine work: a sharp that parts the weave, an overlock needle that takes the same thread, and the single-hole plate that stops fine cloth being pushed down into the machine.

The everyday three: a ball point for anything knitted, an overlock needle for the second machine, and a tin of bobbins to wind the thread onto.

Heavier work: the round-shank system for older machines, a set of feet on one shank, and a case with a tension screw you can actually reach.

The industrial end of the wall: two needle systems that will not fit a household machine at all, and the gauge for setting a bar back to the hook after you have had it apart.

  • Domestic needles130/705 H SharpFive to a packet, one size€2.60Over on the wall
  • Domestic needlesELx705 OverlockFive to a packet, one size€3.60Over on the wall
  • Feet and platesStraight-stitch needle plateSteel, one round hole€12.40Over on the wall
  • Domestic needles130/705 H BallpointFive to a packet, one size€2.90Over on the wall
  • Domestic needlesDCx1 (B27) OverlockFive to a packet, one size€3.40Over on the wall
  • Bobbins and casesClass 15 steel bobbinsTen in a tin€4.20Over on the wall
  • Domestic needles15x1 Round-shankFive to a packet, one size€2.80Over on the wall
  • Feet and platesSnap-on foot set, six feetSix feet on one shank€14.80Over on the wall
  • Bobbins and casesClass 15 drop-in caseSteel, with the tension screw€9.50Over on the wall
  • Industrial needlesDBx1 (1738)Ten to a packet, one size€5.40Over on the wall
  • Industrial needlesDPx5 (1901)Ten to a packet, one size€5.80Over on the wall
  • Drive and benchNeedle-bar timing gaugeSteel, sets the bar to the hook€21.00Over on the wall

Bring the old needle.

We read the shank and the flat off it. Those two things decide whether a packet will fit your machine at all, and nothing printed on a box can tell us instead.

One size to a packet.

No mixed packs on this wall. If you want 70 and 90 you take two packets, because the one you want is the one you will reach for in the dark.

Belt cut to length.

Toothed belt comes off a roll behind the counter. Bring the old one, or a string run round both pulleys and knotted where it meets.

Four off the wall

All sixteen on the wall
Cones of thread on steel shelving in a store roomDomestic needles

ELx705 Overlock

€3.60

Five to a packet, one size

Brown woven cloth lit from one sideFeet and plates

Feed dog, 6 mm wide

€7.90

Steel, two rows of teeth

Steel spanners hanging on a perforated boardDrive and bench

Counter service kit

€16.50

Oil, two brushes, three drivers

Everything the wall carries

Sixteen lines, five shelves. Every line on this list is in a drawer behind the counter, and no line is sold as fitting a machine nobody here has seen.

  • Five systems

    Domestic needles

    130/705 H sharp and ball point, 15x1 round shank, and two overlock systems. Sizes 60 to 110 on the shelf, 120 on the day.

    See that shelf
  • Two systems

    Industrial needles

    DBx1 and DPx5, ten to a packet. Neither will go into a household machine, and that gets said at the counter rather than after.

    See that shelf
  • Three lines

    Bobbins and cases

    Class 15 steel bobbins by the tin, the drop-in case to go with them, and the little rubber tyre the winder runs on.

    See that shelf
  • Three lines

    Feet and plates

    A six-foot set on one snap-on shank, the straight-stitch plate with a single round hole, and a feed dog with two rows of teeth.

    See that shelf
  • Three lines

    Drive and bench

    Toothed belt off the roll, the oil and brushes kit, and the steel gauge that sets a needle bar back to the hook.

    See that shelf
A wall of wooden drawers in an ironmonger, each front showing the small parts kept inside

The drawer fronts carry one of each thing inside them, which is how you find a part whose name you never learned.

What the groove has to hold

The groove is the channel running up the front of the blade. While the needle is down, the thread lies in it, and the cloth closes round the blade rather than round the thread. That is the whole job: shelter.

Put a thread in a groove too shallow for it and part of it stands proud. Every stitch then drags that standing part against the weave, and after a few hundred stitches it is fibre rather than thread. People usually blame the thread.

The other way round is quieter but just as real. A blade far coarser than the thread needs makes a hole wider than anything that has to fill it, and on a fine weave the hole stays open.

Groove, point and gauge
A pale linen weave photographed close up, the threads crossing in both directions
A close weave of pale blue and white loops seen from directly above

A needle is finished long before it looks it. The tip rounds over, and a round tip pushes the cloth instead of piercing it — so the loop does not form, and the machine misses a stitch. People bring the machine in. Nine cases in ten it is the needle, and the needle looks perfect.

Egidijus Vaišvila, behind the counter since 1998

If the size is not obvious

Tell us the thread and the cloth

Write down what is printed on the reel and what you are sewing into, and the packet comes back by return. Where a part cannot be named off a photograph, that gets said plainly instead of guessed at.